拉曼光谱 » 讨论区 » 经验共享 » 【求助】石墨化碳的拉曼光谱是不是只在1580cm-1有一个峰?

采购询价

点击提交代表您同意 《用户服务协议》 《隐私政策》

 
需要登录并加入本群才可以回复和发新贴

标题:【求助】石墨化碳的拉曼光谱是不是只在1580cm-1有一个峰?

wwwh[使用道具]
一星
Rank: 6Rank: 6


UID 128411
精华 0
积分 3084
帖子 1727
信誉分 100
可用分 10252
专家分 0
阅读权限 255
注册 2014-11-1
状态 离线
1
 

【求助】石墨化碳的拉曼光谱是不是只在1580cm-1有一个峰?

站内搜索了下,发现讨论的高人挺多,可是还是有一些疑问:
石墨化碳的拉曼光谱是不是只在1580cm-1有一个峰?
而无定形碳只在1340cm-1有一个峰?
如果1340和1580处各有一个峰,是不是就代表所测碳材料部分石墨化?
看到一篇文章里面有这样一段描述,不是很明白
The Raman spectrum of the as-obtained
carbon microtubes is show in Figure 4, in which a broad peak
at 1334 cm-1 as well as a sharp absorption peak at 1600 cm-1
can be clearly seen. The peak at 1334 cm-1 is usually associated
with the vibrations of carbon atoms with dangling bonds for
the in-plane terminations of disordered graphite and is labeled
as the D-band, and the peak at 1600 cm-1 (G-band) (corresponding
to the E2g mode) is closely related to the vibration in
all sp2 bonded carbon atoms in a 2-dimensional hexagonal
lattice, such as in a graphene layer.26,27 The intensity ratio of
the D to G band (ID/IG) is calculated to be 0.64, further reflecting
the relative disorder and low graphitic crystallinity of the CMTs.
顶部
aaby[使用道具]
五级
Rank: 5Rank: 5


UID 127161
精华 0
积分 2602
帖子 1423
信誉分 100
可用分 8733
专家分 0
阅读权限 255
注册 2014-9-14
来自 内蒙古乌兰察布市集宁
状态 离线
2
 

回复

要分峰拟合,ID/IG是分峰拟合后两个峰的面积比,这个值越小,表示石墨化程度越高。
参见:
1. Sadezky A, Muckenhuber H, Grothe H, et al. Raman microspectroscopy of soot and related carbonaceous materials: Spectral analysis and structural information . Carbon, 2005, 43(8): 1731-1742.
2. Sheng C. Char structure characterised by Raman spectroscopy and its correlations with combustion reactivity . Fuel, 2007, 86(15): 2316-2324.
顶部
p1900[使用道具]
一星
Rank: 6Rank: 6


UID 129716
精华 0
积分 3273
帖子 1925
信誉分 100
可用分 11045
专家分 0
阅读权限 255
注册 2014-12-17
状态 离线
3
 

回复

ID/IG越小,石墨化越低吧,D峰对应的是石墨团簇的尺寸大小
顶部
hcy517[使用道具]
五级
Rank: 5Rank: 5


UID 128273
精华 0
积分 2933
帖子 1725
信誉分 100
可用分 10050
专家分 0
阅读权限 255
注册 2014-10-28
状态 离线
4
 

回复

貌似只要是碳材料,都有G峰的
顶部
xiaoxiaojinglin[使用道具]
五级
Rank: 5Rank: 5


UID 131600
精华 0
积分 2351
帖子 1302
信誉分 100
可用分 7817
专家分 0
阅读权限 255
注册 2015-1-31
状态 离线
5
 

回复

只要是碳材料,1580都有峰,即G峰
单晶石墨只在1580出峰
无序碳材料在1580和1340都有峰,文献看D峰相对于G峰的强度越高,石墨化程度越小
顶部
yayayu[使用道具]
五级
Rank: 5Rank: 5


UID 129861
精华 0
积分 2474
帖子 1388
信誉分 100
可用分 8331
专家分 0
阅读权限 255
注册 2014-12-22
状态 离线
6
 

回复

什么叫石墨化程度? 谢谢
顶部
哈密瓜[使用道具]
五级
Rank: 5Rank: 5


UID 128271
精华 0
积分 2135
帖子 1149
信誉分 100
可用分 7083
专家分 0
阅读权限 255
注册 2014-10-28
状态 离线
7
 

回复

MM这个强度是面积还是峰高啊
顶部
大花猫bb[使用道具]
五级
Rank: 5Rank: 5


UID 128333
精华 0
积分 2935
帖子 1649
信誉分 100
可用分 9653
专家分 0
阅读权限 255
注册 2014-10-30
状态 离线
8
 

回复

我们的名字倒很像,就是你的这个公式记错了吧,G带越高,石墨化程度越高吧
顶部