(5)F5:grinding motor 砂带马达
on (开) off(关)
F1 F3
(6)F6:cooling station 冷却水系统
Cooling basin cooling water sample dryer
冷却水门 冷却水 出样口样品干燥气
←→→← on off F8
F1 F3 F5 F6 (按下即开,松开即关)
(7)F7:除尘器Exhauster
on (开)
F2(按下即开,松开即关)
(8)F8:进样门,出样门 noise protection system
Noise protection cover input door
出样门 进样门
open (开) close(关) open(开) close(关)
F2 F4 F6 F8
注意:①F2(步进马达)不要进入,初始值为1992 2032;
②摇臂在90°时,不要手动让出样门关闭;
③手动中最常用为F8(进样门和出样门)、F1(摇臂)、F5
(砂带马达)作者: wccd 时间: 2010-6-23 15:05
3、注意事项:
手动与F16合用
(1)两个样品叠在一起时,应先手动抬摇臂,再摇摇臂到60°,再F16复位。
(2)砂带没停时,应先手动停砂带,再F16复位;若摇臂下降,就先抬摇臂。
(3)步进马达在中间时,应先按F16复位2分钟,若不行,可手动调整为1992 2032。
(4)如果出样门卡住,就推一下门即可。
(5)仪器不开时,仪器内部不能有样品。
(6)当开始要自动磨样时,不要站在出样门旁以免被夹伤。
4、错误信息:
(1)○09Emergency stop pressed 紧急止动钮被按
(2)○32production sample prepairing procedure cannot be started, because no samples is available 样品没放好,所以无法执行研磨过程。
(3)○02 密码错
(4)○28 “right side”右偏 用手轮向反方向旋转
(5)○27 grinding left side 左偏 (不能超过 土半圈)
(6)○10 absence of compressed air 没有压缩空气
(7)battery control CPU has been activated replace battery
CPU 没有 电池 请换电池
(8)○25 The grinding belt is not tighted砂带没绷紧
(9)○26 The grinding belt is torn 砂带断裂
(10)○14 cooling water is not available 无冷却水
(11)○33 sample preparing procedure can not be started, because the input door is not closed 进样门没关,无法进行自动状态
(12)○40 sample lost or too thin 样品没抓住或太薄
(13)○42 system not in home position 位置没在初始状态
(14)○35 It is not possible to return to the home position ,because the input door is not closed 因为进样门没关无法回到初始状态
(15)注意事项:
手轮不要轻易转动,以防砂带跑偏
如果砂带左偏,手轮则右转,每次只能转一点,不能超过正负半圈。
5、砂带磨样计数器清零:作者: wccd 时间: 2010-6-23 15:07
5、砂带磨样计数器清零:
(1)首先出现“03 please , change the grinding belt and clear the actual value change menu with:‘F8’”请更换砂带并给计数器清零,首先用“F8”进入清零菜单。
(2)○5 grinding counter set point:×××
原设置定值为:×××
○2actual value :×××
实际磨样值为:×××
○3 please change the grinding belt and clear the actual value with “F8”and“ENT”
看完○1○2项后,请同时按住“F8”和“ENT”为计数器清零。
○4按“CLR”退出
6、F8(在初始状态的作用)
① grinding counter set point :400
一条砂带原设定磨样次数为:400
②actual value:6
实际磨样次数为:6
③按“↓”,sample preparing time:××× Seconds
当前样品研磨处理时间为 ××× 秒
④若回去看,按“↑”;若要退出,按“CLR”
初始状态:
(1) 摇臂30°;(2)摇臂上升状态;(3)夹子开;
(4)压板上升状态;(5)进样门关;(6)出样门开;
(7)步进马达位置为01992 02032
(8)所有气嘴关;(9)砂带马达关;(10)冷却水关;
(11)冷却水门关 (12)除尘器关
若初始态不对,一般应看出样门和步进马达位置。作者: wccd 时间: 2010-6-23 15:08