光电直读光谱

　　0.ALARM ICS:Instrument busy(executing M1,M2,IS,CS command)

　　1.ALARM# ICS:Instrument vacuum out

　　2.ALARM# ICS:Instrument temperature out

　　3.ALARM# ICS:Mains voltage out

　　4.ALARM# ICS:-1000 volt power supply out

　　5.ALARM# ICS:cabinet temperature out

　　6.ALARM# ICS:+5 volt power supply out

　　7.ALARM# ICS:+15 volt power supply out

　　8.ALARM# ICS:-15 volt power supply out

　　9.ALARM# ICS:+24 volt power supply out

　　10.ALARM# ICS:-100 volt power supply out

　　11.ALARM# ICS:-10v test out(ICS 35)/+5v SEQ out (ICS34/3520)

　　12.ALARM# ICS:-1v test out(ICS 35)/+15v SEQ out (ICS34/3520)

　　13.ALARM# ICS:-0.1v test out(ICS 35)/-15v SEQ out (ICS34/3520)

　　14.ALARM# ICS:charge converter zero reference out(ICS-35)

　　15.ALARM# ICS:CCS/DCU +350 Volt power supply out

　　16.ALARM# ICS:CCS/DCU +200 Volt power supply out

　　17.ALARM# ICS:CCS/DCU +15 Volt power supply out

　　18.ALARM# ICS:CCS/DCU -15 Volt power supply out

　　19.ALARM# ICS:CCS/DCU +5 Volt power supply out

　　20.ALARM# ICS:CCS/DCU +25 Volt power supply out

　　21.ALARM# ICS:Instrument safety circuit broken

　　22.ALARM# ICS:Instrument STOP button pressed

　　23.ALARM# ICS:Source not running

　　24.ALARM# ICS:Lower voltage out

　　25.ALARM# ICS:Charge converter overflowor underflow

　　ALARM前面的编号是仪器出现警告的编号。是一一对应的

　　26 ALARM# ICSata supplied to ICS out of range

　　27 ALARM# ICS:No instrument START

　　28 ALARM# ICS:Incorrect ACS Command sequence

　　29 ALARM# ICS:Reading attempted with no measure

　　30 ALARM# ICS:Power up instrument controller

　　31 ALARM# ICS:Link ICS-MSC USART-2,ICS Input buffer full

　　32 ALARM# ICS:Link ICS-MSC USART-1,ICS Input buffer full

　　33 ALARM# ICS:Autosampler timeout

　　34 ALARM# ICS:Command not executed bu ICS

　　35 ALARM# ICS:Link ACS-ICS USART-1,checksum error

　　36 ALARM# ICS:Illegal command received from ACS

　　37 ALARM# ICS:Link ACS-ICS USART-1,transmission error

　　38 ALARM# ICS:Illegal ACS string format to ICS

　　39 ALARM# ICS:Undefined status parameters on ICS

　　40 ALARM# ICS:Robot'breackdown' detected by ICS

　　41 ALARM# ICS:Link ICS-MSC USART-2,checksum error on MSC

　　42 ALARM# ICS:SEQ:ERR.GRATING 1 on

　　43 ALARM# ICS:SEQ:ERR.GRATING 2 on

　　44 ALARM# ICS:Optical filter carrousel unsynchronised

　　45 ALARM# ICS:Illegal optical filter nr selection

　　46 ALARM# ICS:SEQ:Invalid command

　　47 ALARM# ICS:SEQ:Lambda too high

　　48 ALARM# ICS:SEQ:M1:2 switchs on

　　49 ALARM# ICS:SEQ:M1:2 limit error

　　50 ALARM# ICS:M1 locked at SW1

　　MIO--Manual ICS Dialogue File ---------------Terminal Mode commands used for QA facilities

　　MSK--Database-------------------------------- Instrument alarms and modification reasons.

　　MVR--MVR save state File--------------------- All data saved resulting from Regression computations.

　　PRG--Analytical program Files-----------------Global Analytical Data for Analysis

　　QUA--Quality File-----------------------------All data related to Quality used for Quality check.

　　RXB--Reception Buffering File-----------------This contains data received from device i.e.EXAN.

　　S1--Main database File-------------------------Contains instrument

　　configuration,analytical conditions setting-up samples,...

　　S2--Main database File------------------- -----Contains instrument configuration,analytical conditions setting-up samples,...

　　SEL--Material selection file--------------------Global data using Material used for change correction

　　SRC--Import/Export Raw--------------------------Error Massage,Data File Alarm,etc.Used for Database Generator,These Files may be copied and then imported into the Database.